Home
>
products
>
Mold Cleaning Agent
>
|
|
| Place of Origin | China |
| Brand Name | JT-RESIN |
| Certification | SGS，CE,UL |
| Model Number | JT6103 |
JT 6103 epoxy resin mould cleaning agent of 66KV Dry Type Transfomer
What are the recommended safety procedures and guidelines for using Jiangte's cleaning and release agents?
Here are some general safety procedures and guidelines that should be followed when using Jiangte's cleaning and release agents:
Read the Safety Data Sheet (SDS): The SDS provides important information about the hazards and safe handling practices for the specific cleaning and release agent. It is important to read the SDS carefully before using the product.
Wear Personal Protective Equipment (PPE): Wear appropriate PPE, such as gloves, safety glasses, and protective clothing, when handling the cleaning and release agents. This can help to protect against skin and eye irritation or other hazards.
Use in a Well-Ventilated Area: Use the cleaning and release agents in a well-ventilated area to minimize exposure to vapors and fumes. If ventilation is inadequate, use respiratory protection.
Follow Recommended Dilution Ratios: Follow the recommended dilution ratios for the cleaning and release agents. Over-diluting or under-diluting the agents can affect their effectiveness and safety.
Store Properly: Store the cleaning and release agents in a cool, dry, and well-ventilated area. Keep the agents away from heat sources, flames, or other ignition sources.
Avoid Contact with Skin and Eyes: Avoid direct contact with the cleaning and release agents. If contact occurs, rinse the affected area with plenty of water and seek medical attention if necessary.
Dispose of Properly: Dispose of the cleaning and release agents in accordance with local regulations. Do not dump the agents down drains or into the environment.
Overall, it is important to follow all recommended safety procedures and guidelines when using Jiangte's cleaning and release agents to ensure safe and effective use.
|
JT 6103 epoxy resin mould cleaning agent Product
|
|
|
For mould cleaning, can strongly remove the alkyd, carbonization, Silicone oil Application wax, rubber, oil(etc) on the surface of the mold, to make the mold surface looks like new one |
|
|
non-irritating smell Features hot mould , no need cooling, can be cleaned directly, which greatly improving work efficiency odorless,non-toxic,harmless,fully comply with environmental protection requirements low using amount,low cost,strong decontamination, saving cost for your product high boiling point and bring unusual rich bubbles, which will not easy to burn workers when they operate high temperature mould not damage the mould, life span can be extended |
|
|
A. Dispersion method: Spread or daub on high temperature mould with a small amount of stoste or diluent, and after 2-3 minutes, contaminants will soften and dissociate. Washing it immediately with water before drying
B. pickling process: Put the stoste or diluent into the groove, heat to 95℃(about) and soak for about 2-4minutes, or put the high temperature mould into the normal atmospheric temperature solution, soak for about 2-4minutes, and after that take it out and wash it with water
According to pollution level of mould, properly select solution concentration,dip time,solution temperature. Dip, remove dirt, for a long storage. New liquids must be added if using again |
Methods
|
|
Hubei Jiangte Insulation Composite Guangzhou Jiangte Insulation Composite Add:No.219,Zhanghua Rd(N),Economic & Development Add:Rm606,DongHong International Plaza, No.113 Zone of Qianjiang City, Hubei Province, China. Chebei Rd, Tianhe District, Guangzhou, China. Tel:+86-728-6201068 Tel:+86-20-82320316 Fax:+86-728-6202066 Fax:+86-20-82315407
|
|
Safety operation:
freezing of products are prohibited, If frozen, using mechanical stirring to keep the product uniformity;
This product has no toxicity, no smoking when operation. Before using, refer to MSDS(material safety data sheet) first.
Package:
25Kg/container
3. COMPOSITON INFORMATION ON INGREDIENT
| Chemical Name | CAS No. | Content(%) |
| Methanol | 67-56-1 | 50.00 |
| Light aromatic solvent naphtha | 64742-82-1 | 50.00 |
4. FIRST AID MEASURES
A. Eye contact
- Do not rub your eyes.
- Immediately flush eyes with plenty of water for at least 15minutes and call a doctor/physician.
B. Skin contact
- Flush skin with plenty of water for at least 15minutes while removing contaminated clothing and shoes.
- Laundering enough contaminated clothing before reuse.
- Go to hospital immediately if symptoms(flare, irritate) occur.
- Wash thoroughly after handling.
C. Inhalation contact
- When exposed to large amounts of steam and mist, move to fresh air.
- Take specific treatment if needed.
D. Ingestion contact
- About whether I should induce vomiting. Take the advice of a doctor.
- Rinse your mouth with water immediately.
E. Delayed and immediate effects and also chronic effects from short and long term exposure
- Not available
F. Notes to physician
- Notify medical personnel of contaminated situations and have them take appropriate protective measures.
5. FIRE-FIGHTING MEASURES
A. Suitable (Unsuitable) extinguishing media
- Dry chemical, carbon dioxide, regular foam extinguishing agent, spray
- Avoid use of water jet for extinguishing
B. Specific hazards arising from the chemical
- Not available
C. Special protective actions for firefighters
- Notify your local firestation and inform the location of the fire and characteristics hazard.
- Using a unattended and water devices in case of large fire and leave alone to burn if you do not imperative.
- Avoid inhalation of materials or combustion by-products.
- Do not access if the tank on fire.
- Use appropriate extinguishing measure suitable for surrounding fire.
- Keep containers cool with water spray.
- Vapor or gas is burned at distant ignition sources can be spread quickly.
6. ACCIDENTAL RELEASE MEASURES
A. Personal precautions, protective equipment and emergency procedures
- Must work against the wind, let the upwind people to evacuate.
- Move container to safe area from the leak area.
- Remove all sources of ignition.
- Do not direct water at spill or source of leak.
- Avoid skin contact and inhalation.
B. Environmental precautions
- Prevent runoff and contact with waterways, drains or sewers.
- If large amounts have been spilled, inform the relevant authorities.
C. Methods and materials for containment and cleaning up
- Large spill : Stay upwind and keep out of low areas. Dike for later disposal.
- Notification to central government, local government. When emissions at least of the standard amount
- Dispose of waste in accordance with local regulation.
- Appropriate container for disposal of spilled material collected.
- Small leak: sand or other non-combustible material, please let use absorption.
- Wipe off the solvent.
- Dike for later disposal.
- Prevent the influx to waterways, sewers, basements or confined spaces.
7. HANDLING AND STORAGE
A. Precautions for safe handling
- Wash thoroughly after handling.
- Avoid direct physical contact.
- Avoid contact with incompatible materials.
- Refer to Engineering controls and personal protective equipment.
- Do not inhale the steam prolonged or repeated.
B. Conditions for safe storage, including any incompatibilities
- Do not use damaged containers.
- Do not apply direct heat.
- Save applicable laws and regulations.
- Avoid direct sunlight.
- Keep in the original container.
- Collected them in sealed containers.
- Do not eat, drink or smoke when using this product.
- Store away from water and sewer.
8. OPERATION DISPOSAL AND STORAGE
Note: closed/sealed operation, provide good natural ventilation condition. The operator must go through specialized training, strictly follow the operating rules. We suggest that the operating personnel wearing Self suction filtering type dust mask, and wearing protective chemical safety glasses.
Storage note: dry and ventilated
9. PHYSICAL AND CHEMICAL PROPERTIES
| -Appearance | |
| a. Appearance | Liquid |
| b. Color | Colourless |
| -Odor | Solvent |
| -Auto-ignition temperature | 385 ℃ |
| -Melting point/ freezing point | 187 ℃(lit.) |
| -PH | No data available |
| -Flash point | Approx. 50 ℃ |
| -Density | 0.70-0.90g/cm3 (at 25℃) |
| -Viscosity | No data available |
10. STABILITY AND REACTIVITY
A. Chemical Stability and Reactivity
- This material is stable under recommended storage and handling conditions.
B. Possibility of hazardous reactions
- Hazardous Polymerization will not occur.
C. Conditions to avoid
- Avoid contact with incompatible materials and condition.
- Avoid Accumulation of electrostatic charges, Heating, Flames and hot surfaces.
D. Incompatible materials
- Not available
E. Hazardous decomposition products
- May emit flammable vapour if involved in fire.
11. TOXICOLOGICAL INFORMATION
Acute oral toxicity : LD50 rat
Dose: > 2,000 mg/kg
Eye irritation : irritating rabbit
Method: Data based on tests on similar product.
Skin irritation: irritating rabbit
Method: Data based on tests on similar product.
dermal
Sensitization: Causes sensitization. Guinea pig
Method: Data based on tests on similar product.
Dermal
12. ECOLOGICALINFORMATION
Ecological toxicity: unknown
Biological degradation: unknown
Non biological degradation: unknown
13. DISPOSAL CONSIDERATIONS
A. Disposal methods
- Since more than two kinds of designed waste is mixed, it is difficult to treat separately, then can be reduction or stabilization by incineration or similar process.
- If water separation is possible, pre-process with Water separation process.
- Dispose by incineration.
- Incinerate the oil by separating the oil and water
- The remainder of the water after separation will be processed in a water pollution prevention facilities.
- Do incineration or stabilization of the residue after disposal as the method of evaporation and concentration.
- Do incineration of the residue after disposal as the method of agglomeration and precipitation.
- Take care of incinerate or stabilization after treatment, purified by means of Separation distillation extraction filtration pyrolysis
B. Special precautions for disposal
- The user of this product must disposal by oneself or entrust to waste disposer or person who other’s waste recycle and dispose, person who establish and operate waste disposal facilities.
- Dispose of waste in accordance with all applicable laws and regulations.
14. TRANSPORT INFORMATION
DOT (US)
UN-Number: 1230
Class: 3
Packing group: II
Proper shipping name: FLAMMABLE LIQUID
Marine pollutant: No Poison
Inhalation Hazard: No
IMDG
UN-Number: 1230
Class: 3
Packing group: II
EMS-No: F-E S-E
Proper shipping name: FLAMMABLE LIQUID
Marine pollutant: No
IATA
UN-Number: 1230
Class: 3
Packing group: II
Proper shipping name: FLAMMABLE LIQUID
Transport note: checking the packaging container whether complete and sealed or not before transport, make ensure that the container does not leak, do not collapse, not falling, not damaged. Mixing packing and transport with oxidant and food chemicals is prohibited. Transport vehicle must be thoroughly cleaned, disinfected, otherwise it can not load other goods. When loading, the assemble location should be far away from the bedroom, kitchen, and separate from engine room, power supply, fire and other parts. Highway transport need to follow the regulations and drive as per stipulated route
15. REGULATORY INFORMATION
National legislation
Flammable
Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
Harmful: may cause lung damage if swallowed.
Repeated exposure may cause skin dryness or cracking.
Notification status : EINECS yes
: TSCA yes
: DSL yes
: INV (CN) yes
: KECI (KR) yes
: JEX (JP) yes
Contact Us at Any Time
